How to install a fishfinder on a bass boat

Setting Out the Cable. Instead cut the wires and leave the original transducer in place.

More often than not a transom mount transducer is very easy to install on to a boat.

How to install a fishfinder on a bass boat. If youre installing your fish finder in the console of your boat you have three primary strategies. The one you choose depends on the size of your fish finder how much room you have on the console and the size of your boat. This is what we call flush mounted fish finders.

This is the most desirable look for a bass boat. When it comes to all kinds of fish finders installing the transducer is critical especially if you are making use of solar imaging sonar and down imaging. Buying a transducer mounting board helps in a big way.

You can install it on the transom of the boat. Use two screws to secure it in place. HOW TO Install Fish Finders on a Bass Tracker Pro Team 175 TXW Lowrance Garmin Ram Mount - YouTube.

HOW TO Install Fish Finders on a Bass Tracker Pro Team 175 TXW Lowrance Garmin Ram Mount. The first step in how to install fish finder whether installing on a kayak bass boat or cruiser is figuring out where you want the fishfinder to be. Locating the fish finder on your boat should be a process not taken lightly.

Theres nothing worse than getting everything installed and learning that it just wont work there. Neither one is very difficult to install if you have basic hand tools and are a little handy. The hardest part will be running the wires for the depth finder.

The power pole is easy. I just bought a used fish finder hummingbird 120 or something and want to install it on my boat until i get a better newer unit w GPS. I have the unit itself the transducer a speed wheel wiring etc but the power cords look too short the power cords from the unit which will hookup to the battery are only 3-4 feet long.

Install your fish finder on your kayak in less than 5 minutes and remove it even faster. Dont drill any holes when installing your transducer onto your kayak. Dont glue your transducer into the hull of your kayak or any other boat its better being directly in the water - where we mount it.

You might have to splice two wires together to get the right length you need when installing a fishfinder on your boat and the neatest way to secure the splice is with shrink tubing. Once the splice is done and tested pull some shrink tubing over it and seal with a heat gun. You can also use electrical tape but its not as neat.

Here are the steps that will help you in fitting your fish finder properly. Finding the Perfect Place for the Transducer. This may be the most critical of all the steps in the fish finder installation process.

More often than not a transom mount transducer is very easy to install on to a boat. I currently have a Humminbird 787c2i fish finder located on the boat dash and would like to install a second unit in the bow. After speaking to a Humminbird customer service rep.

I was told a second unit cannot be added using the same transducer I would have to use a switch and only operate one unit at a time and adding a second fish finder and. Place the ducer in the glob of stuff and give it a quarter turn while pushing it down to the bottom of the glue. At this point I let it sit for 24 hours to make sure the adhesive fully set up.

Regardless of how long you choose to wait dont let it get wet until fully cured. How to install a fish finder. Installing a fish finder is not an easy task.

There are many things that can go wrong but its possible to install one if you follow the instructions step-by-step. The first thing to do is to clean the boat hull and then drill into it with a hole saw attachment on your power drill for about 3 inches in diameter. Using the boat wiring harness is OK as long as you stay with simple low featured electronics.

If you get more sofisticated electronics the boat wiring harness conductors are so small they have too much resistance to support the higher amperage units. I put Side Imaging at the bow of my PT 170 TX and ran 12 guage marine grade wring to the bow. The one thing that the boat were going to look at doesnt have that wed like is a fishfinderdepth finder.

I saw some at the store yesterday locally really surprised the local farm store had them but they have huntingfishing supplies so I guess it made sense they even carry 2 and 4 cycle oil boat anchors seat replacements bumpers the water thing for doing the winterizing on engines. If not dont risk damaging the hull. Instead cut the wires and leave the original transducer in place.

Within this same area select a clean level spot to install the new transducer. Prep the mounting area by roughing with fine sandpaper or a Scotch-Brite pad. Install the binnacle give each bolt a little bit of sealant and then secure the bolts.

Give Your Fishfinder Power. Using the exit hole that youve already drilled through the back feed the power leads through. There should be enough slack on the plugbut not.

How To Install A Fishfinder On Fiberglass Boat. Wrapping Up the Installation. Installing A Transducer On Fiberglass Boat.

Setting Out the Cable. When its Possible to Cut the Transducer Cable.