12
May
The transom installation which is the most widely used. Otherwise youll need to get a wire fish and start from scratch to pull the new transducer wire and plug through.
Fish your transducer cord along the same path.
How to install a fishfinder on a fiberglass boat. How to Install a Fishfinder on a Fiberglass Boat. Installing a fishfinder might sound like a painfully long and complicated feat however it is much simpler than it sounds. With that in mind we have concocted a review laying down all the steps.
We hope that these step by step guidelines will help our readers in successfully installing their own fishfinder with little to no extra help. In order to install a Fishfinder on your fiberglass boat you will need. A fishfinder either an echo sounder or side-scan sonar model this depends on the type of fishing you are doing such as roach fishing carp fishing salmon fishing perch fishing etc.
Mounting hardware bolts nuts washers and mounting brackets that are specific to your boats make and model. With the wiring pulled through coil any extra line inside making sure to secure with clamps and never to cut the wire for length as it may affect the way your fishfinder performs. Keep the transducer wire separate from the engines wiring harness as well as the VHF cable.
Installing and placing the fish finder. Have the right place in mind for the transducer bracket. Hold it against the transom and until you get the best position move it around.
Make a marking of where the mounting holes of the bracket end up. How To Install A Fishfinder On Fiberglass Boat. Wrapping Up the Installation.
Installing A Transducer On Fiberglass Boat. Setting Out the Cable. When its Possible to Cut the Transducer Cable.
Lowrance Elite-5 Bayliner Capri IO. This is a step by step instructional video on installing a Lowrance Elite 5 DSI Combo Chartpoltter Fishfinder. Other brand units will install the same way.
Put a fuse on the positive right up close to the battery. 5 amp fuse is good. As for the transducer cable it is fairly standard to drill a hole under the swim platform above the water line.
Hole should be at least double diameter of cable. Big enough to be able to seal around the cable tight with marine grade sealer. Some have taken a thick plastic board and glued it to the transom and then mounted the transducer to it.
But for the 3 small holes the screws make and a little 4200 on them when installed I dont see the problem. Just put 2 of them on the transom of my. If not and if your boat had an old fishfinder with a transom mount than wont be re-used cut the transducer off the end and use the old wire to draw the new one through the wiring chase.
Otherwise youll need to get a wire fish and start from scratch to pull the new transducer wire and plug through. To install the transducers mounting ring locate an area on the hull then sand the area to smooth out the bottom. Then coat the bottom of the ring with a liberal amount of GTE Sealant I or II as called for in the installation instructions and glue the ring to the boat hull.
Provide a fill spout and cap to add fluid. Cut and position the base of the housing so it will be mounted vertically. Secure the housing to the hull with Marine-Tex for a watertight seal.
Mount the transducer through a hole cut in the top of the housing with the face of the transducer facing downward. How to install or mount a sonarfishfinder transducer without drilling damaging holes in your boat - YouTube. How to install or mount a sonarfishfinder transducer without drilling damaging holes.
They either leave the areas 100 fiberglass or use plywood for a backing. As a boat owner perhaps you want to install a VHF antenna. Chances are - especially if the boat has an electronics package option that the boat manufacturer may have created an area in the laminate that has a.
Jon Thelen and Todd Hesse demonstrate how to install a Humminbird transducer in a fiberglass hull. Have a friend hold the other end of the siding as you remove it so that it wont fall and get damaged. Youll see other wires running along the edge of the boat.
Fish your transducer cord along the same path. Fish the wires all the way up to the underside of your consoles instrument panel. How Much Does It Cost to Install a Fish Finder.
Installing a fish finder will take even a seasoned pro a good couple of hours. Therefore if you decide to take your boat and basic fish finder to a professional you should expect to pay anywhere between 200 and 400 for the job. The price will depend on your hired experts hourly rate.
One of the most important steps in a complete and lasting fish finder installation is the quality of wire termination. Be sure to mount your fish finder in a way that holds up to the rigors of fishing trips and rough water. Your Humminbird fish finder includes a transom mounted transducer.
This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat with a two part slow curing epoxy. The transom installation which is the most widely used. Im curious where one would install a fishfinder on the newer dash with 4 connect display.
Im looking at a Garmin striker plus 4 which has a vertical orientation and I need to leave some room for a Perfectpass next year which I would probably mount on the. Learn how to install a transom mount transducer for a fish finder on a boat. To work well a transducer requires immersion in water thats free of air bubbles that cause aeration and result in sonar interference.
Heres how to do it.