03
May
Follow this instructional video and find out how you can easily install one yourselfC. After flipping your kayak back over pull the cable out of the scupper and find a place to keep your battery.
Wrapping Up the Installation.
How to install a fishfinder transducer. Silicone grease or petroleum jelly. The first thing required for installing a fish finder transducer is silicone grease or petroleum jelly. The hull surface is usually not smooth enough for the fish finder transducer to mount and function which is why the.
In this video well go step by step in mounting a 3D fishfinder transducer on a fishing boat this one for a Raymarine Axiom 9. This is a bit different from. Secondly the transducer should be oriented so that it is parallel with the waterline in order to prevent infiltrations.
In other words the centre line of the transducer should be parallel to the bottom of the hull while the front of the RV-100 should ne parallel to the ground. A level and a goniometer can help you in your measurements. Install Fish Finder Transducer in Hull - YouTube.
Installation of a Transom Mount Transducer Main steps. Find the best transducer mounting location. Prepare the mounting location.
Assemble the transducer and perform the initial mounting steps. Route the Transducers Cable through the boat. Connect the Transducer Cable to the transducer.
Installing a Fishfinder transducer. Posted 09-29-2001 0917 PM ET US Hi. Anyone got tips for installation of a transom-mount tranducer.
Lowrance X-15 dual freq skimmer on a 17 Standard. Looking for general tips warnings ideas etc. A fishfinderchartplotter unit is an excellent accessory for any boat.
Follow this instructional video and find out how you can easily install one yourselfC. The Transducer Arm XL is designed for kayaks and canoes with high freeboards and dinghys with a solid transom allowing easy retraction and removal of the depth sounder transducer. With this kit you can install and uninstall your fish finder transducer in a matter of seconds.
No messy adhesives or excessive drilling of fittings required. Double-check with the transducer bracket and then drill one-inch holes. Dont tighten it too hard and give some room if you want to merge it a little deeper.
Fill up these holes with marine silicone and then tighten your bracket with suitable screws. After making sure the battery is switched off connect the power leads then plug the power and transducer wires into the back of the fishfinder. Now hold on a sec.
Before you splash the boat for a test run make sure the 5200 you used to seal the transducer mounting holes has had plenty of time to dry. How to install a fishfinder Adding upgrades to your boat can often seem like a head-scratcher but it doesnt have to be. Let Fishing FinAddict be your gu.
If you want you can attach the transducer directly on the transom. Place it where you want it and drill two holes through the marked areas. Make sure you add a silicone sealant on both sides of the holes to prevent the water from leaking.
You must consider a hummingbird fish finder transducer as an instrument which keeps an eye on the occurrence below the boat. If the transducer does not take place at a best suitable place it will show nothing to you. Following is a step by step guideline of how to install a fishfinder on a pontoon boat.
Wrap excess transducer cable around the mount. DO NOT CUT OR SPLICE your transducer cable Feed the cable through the hole leading to the top of the boat. And re-install the cover over the transducer bay.
After flipping your kayak back over pull the cable out of the scupper and find a place to keep your battery. Whether youre installing a side-finder or a traditional transducer the rest of the steps are the same. With the bracket location identified use the mounting template to mark the transom.
Hold the transducer in place and view it from different angles to be sure youre meeting all the recommended parameters. Finishing the Installation. With these steps in place youre ready to mount the transducer.
Once youve identified the ideal spot for your transducer bracket you should hold it against the transom. Feel free to wiggle it around a bit to make sure that you have the absolute right position. I skip around the lake at full throttle often and can tell you there is quite a bit of pressure on the transducer.
I took the route of installing it the same way they do at CraigCat. Yes the glue tools and block cost a bit but I didt want to take a chance of the transducer flapping around if it came loose or even worse ripping off. Wrapping Up the Installation.
Installing A Transducer On Fiberglass Boat. Setting Out the Cable.