09
Aug
Potentially this can create burned areas on a prop blade 2 Ventilation. Its at the back of the pontoon log close to the bottom.
For Pontoon Boat Lovers.
How to install fish finder transducer on pontoon boat. Now for the hard part. Fishing the wires from the transducer to the helm assuming youre installing the fish finder at the console where it belongs. Start by sliding the fish finders transducer cord into an electrical conduit.
Such material required for the hummingbird fish finder transducer to install a fish finder is as follows. The electric drill having the power of 14 inch. Bolts about 14 having 125 length with at least six pieces of its stainless steel nuts.
Washer both rubber and a metal having quantity 6 at least. To start with select a fishfinder that is suitable to your requirements. Make sure that your fish finder has a transducer along with it as not all fish finders come with transducers.
Here is a guide on how to install fishfinders on a pontoon boat. Position the transducer right. The transducer is a device that changes electric pulses to sound waves.
Wondering if you guys had any ideas on how to mount a fishfinder transducer on a pontoon where it wouldnt get knocked off when beaching the boat. Originally when we purchased the boat the transducer was mounted to the back of a pontoon tube. Unfortunately the mount was one that did not have the flip-up feature found in the newer fishfinder models.
Transducer Placement on a Pontoon Boat Lets make sure we are talking about the proper location. The bracket is not on the top or bottom of the pontoon log. Its at the back of the pontoon log close to the bottom.
Think of the back as a dinner plate. Weld a U shaped aluminim bracket so it does not extend below the pontoon. Installing fish finderdepth finder on pontoon The only logical place for the transducer is at the back of one of the tubes.
If there is no bracket any local weldingfab shop can add one for a few bucks. Do not mount the transducer on the motor pan – there is way too much turbulence in that area and the locator will not read well. Overall the process of installing your fishfinder starts with picking out the best place for your transducer.
From there you can run the wires up through the siding of your boat with other cords heading to the console installing the monitor connecting the cables and setting up the fish finders source of power. For Pontoon Boat Lovers. How to Install a Fish Finder on Your Pontoon Boat STEP BY STEP Do you have any pics to show where.
I picked up a used pontoon boat about 2 weeks ago for a steal which freed up enough to invest in decent electronics. So I got a Lowrance Elite-5 Combo sonar and nav at Cabellas yesterday with the latest MN Lakemaster chip. I cant for the life of me figure out where to mount the damned transducer.
The general tendency for pontoon boat owners is to mount the transducer on one of the pontoons rear bracket on the captains console side usually starboard. This is perfect if youre trolling a lot but it might prove a problem for bass fishermen for instance who spend a lot of time standing at the front of the boat. A trailing transducer when it plows through the water parting it is certain to generate one of a multitude of problems when the transducer is installed inside of the suggested 15.
Potentially this can create burned areas on a prop blade 2 Ventilation. A transducer dragging or plowing anywhere below the running surface of a boat will part the water just as a plowed. Here are some common inside-the-hull transducer models for deepwater applications from Airmar Technology and used by many fish finder brands.
P79 Plastic hull-mount kit 600 watt single or dual frequency 50200 kHz which can be adjusted from 2 to 20 degrees to accommodate for the hulls deadrise. Now on to installing the fish finder mount. You can fix the mount and screw it in with the accompanying stainless steel bolts.
The finish of the bolts is important to avoid corrosion. Fasten each bolt with an aircraft nut and a stainless steel washer for a tight fit with the wrench that came with the fish finder. Use zip ties to connect any loose wire to the pontoon frame.
Connect the transducer wire to the back of the depth finder. Attach the positive and negative connections on the power cable to the boat battery. The positive wire will be red and the negative wire will be black.
View and Download Garmin Striker 4 owners manual online. Screw and insert the screw through the mounting bracket transducer spacer and rubber washer. It is a Choosing the right kayak paddle will give you the best kayaking experience.
Learn how to install a transom mount transducer for a fish finder on a boat. To work well a transducer requires immersion in water thats free of air bubbles that cause aeration and result in sonar interference. Heres how to do it.