How to mount a fishfinder

Equally important is mounting the transducer correctly and in the best location on your boat so you get optimum signal performance. How to install or mount a sonarfishfinder transducer without drilling damaging holes in your boat - YouTube.

Drill your hole right behind your binnacle mount keep it large enough.

How to mount a fishfinder. Mount your fish finder display in a location where you can see it comfortably while driving your boat. Mount your transducer in the location where it gets the best readings. Connect the transducer cables to the fishfinder display so the transducer readings come through.

Connect the power cables to the fishfinder to a battery. How to Install a Fishfinder on a Kayak. 3 Ways to Mount a Transducer - YouTube.

In this video well go step by step in mounting a 3D fishfinder transducer on a fishing boat this one for a Raymarine Axiom 9. This is a bit different from. Drill your hole right behind your binnacle mount keep it large enough.

You can set the binnacle and fishfinder for a moment to ensure enough spacing between your mount and wire holes. With your holes ready use a silicone sealant and apply it around the binnacle mounts base. Do the same around every hole before you run your bolts through.

To install the fish finder mount you can fix it with stainless steel bolts. Make sure to give finishing to your locks to avoid the risk of corrosion. Ensure that the bolts are tightly screwed.

Use duct tape under the mounting area and cut out a cable whole from it. The goal is to mount the transducer so that it is always in smooth water with no air bubbles. Also you want to mount the transducer so the face of the transducer is pointing straight down at thebottom of the ocean.

Take a moment to figure out how or where you are going to mount your transducer. Run the cable through the hole if you have not decided to drill one already if you did decide to drill one make sure you place it where you mount the fishfinder and utilizing a water tight fitting to pull out the cable bring out only enough so that the wire can be plugged in the fishfinder unit flawlessly. How to install or mount a sonarfishfinder transducer without drilling damaging holes in your boat - YouTube.

How to install or mount a sonarfishfinder transducer without drilling damaging holes. The final step in this article on how to install a fishfinder involves completing some smaller jobs and making sure everything on the boat is in shipshape. Seal the wiring holes you made for the mount so that the wires inside are protected.

Here are easy detailed steps on how to properly install a fishfinder on your boat. Mounting the binnacle mount. Before mounting the binnacle on your boat first pick the most suitable position to install it.

Fishfinders vary in size and shape most can be fitted on the helm of the boat easily the helm is easy to reach and has the best view. The device should be in a. You can now mount that transducer.

Simply hold it against the boats surface and follow these instructions to find a good spot. Once youve found an ideal location mark where the bracket should be mounted with chalk or tape so your hands dont slip off during installation. The first step in learning how to use a fishfinder is finding the best location on your boat to mount it.

In most boats the best location to mount a fish finder is on the helm or dashboard area. The helm typically provides the best viewing angle as well as the best access to the depth finder. Can you mount a fishfinder without drilling extra holes.

I believe the thru hull is glued to the inside it reads thru the hull no holes required. But if you already have the transom mount one some use the mounting board as mentioned another method ive seen here if you have an outboard transom mount it to a board then clamp that to the transom. Without a transducer your fishfinder is useless as it is the transducer that sends the signal through the water to receive the pictures on the fishfinder screen.

Equally important is mounting the transducer correctly and in the best location on your boat so you get optimum signal performance. RAM marine electronic mounts are designed with the rubber ball and socket system that provides adjustment points at both ends of the arm. Trusted by anglers around the world choose from clamping drill-down suction cup and track mounting bases to create your perfect mounting solution.

Explore the full line of RAM fishfinder and chartplotter mounts below.