How to tie a hook for bass fishing

Pull the nose of the Fluke up the hook shaft to cover the eye of the hook and then run the hook point up through the belly. What Gear to Use.

Tie a stop knot behind the last bead.

How to tie a hook for bass fishing. Your line is ready and your hook and bobber are tied on. Place your bobber 6-12 from your rod tip and make sure your line is not wrapped around your rod. Before you cast look behind you to be sure no one else is there.

How to Fish for Bass with Drop Shot Rig. Control the weight of your rig. If youre bass fishing in deeper waters use slightly heavier weights.

The most common sinker bullets weigh about ⅛ oz - ¼ oz 35 g - 7g. Move the rig very slowly and calmly dont shake and move it too fast. Give the bass some time to notice the rig and attack it.

Nightcrawler rigged just like you would a plastic worm on a worm hook. Great option for bass. Grab your hook and the nightcrawler.

Gently thread your worm hook through the nose of the worm through the head and out just like you would a plastic worm. Pull the full bend of the hook out of the crawlers body and then turn the hook point back into the worm. Fold the route to the middle or half of the rope and place it in a hook direction with the end pointing to the left of the hook.

Tie a Palomar along the end of the tag but do not strain the knot immediately. Then put the hook through the looped end of the line. For enhanced safety moisten the line on the looped portions.

Tie in 4 strands of flash on one side of the hookmaterials fold it over and tie them on the other side. Trim these to about the length of the tail. Take a small bunch of bucktail light blue in this pattern clean out the underfur and short hairs and tie about 6-7.

The Texas Rig is one of the most popular bass fishing rigs. It is a way to fish a soft plastic worm close to or in cover such as weeds. This rig requires a special cone-shaped weight and a worm hook which is designed to be threaded through the worm so that the point of the hook is not exposed.

Snell a circle hook to an 8-inch length of 80-pound-test mono. Use a double-barrel sleeve to connect the leader to one eye of the three-way swivel so there is no more than 4 inches between the hook and the swivel. Crimp the sleeve and remove the excess mono.

Tie the main line to the second eye of the three-way swivel. First tie a 2ft amnesia hooklength to one end of the swivel. Then tie a similar length of rig body line to the other end.

Slide two beads onto the line two beads help the line stand out more. Slide on the pulley bead and another bead behind it. Tie a stop knot behind the last bead.

Tie a lead clip onto the other end of the rig body line. Fishing a lizard weightless is a great way to catch finicky bass. This is the simplest lizard rig of all of them.

Just put your lizard on the hook and start casting. You can fish a lizard just like you would a wacky rig. A wacky rig is usually a senko style of worm with a.

Take the fishing line through your bullet-style weight and the eye your preferred hook. Then tie your Palomar knot. Although other knots are.

Pull the nose of the Fluke up the hook shaft to cover the eye of the hook and then run the hook point up through the belly. This rig works well with traditional worm hooks extra wide gap EWG style hooks as well as straight shank hooks. With a straight shank hook you will leave the hook point just below the surface of the baits back.

Best Jig for Bass Fishing. Types of Bass Jigs. Best Bass Jig Trailers for Bass Fishing.

Bass Fishing Jig Techniques You can Use. Where and When to Use Bass Fishing Jigs. Bass Fishing Jig Setup.

What Gear to Use. First things first you need to have the right gear if you expect to have any success with jigging.