How to wire fish finder to fuse box

The unit fuse sizes are 3A each. Using only marine-grade wire shrink tubing fuse.

Assuming that your fish finder comes with its fuse kit you will get all your connectors and wires.

How to wire fish finder to fuse box. Connecting To the Fuse Box. Follow our simple step-by-step guide below to connect your fish finder to the fuse box. Identify an Open Fuse Terminal.

First you need to locate an unused spot within your fuse box. Cut off the Inline Fuse and Battery Connectors. Next cut off the battery connectors and inline fuse if applicable.

With your fish finder unit you will get all the connectors and wires. The connection wire actually comes with a top cut-off for easy wiring. Insert the wires into the butt connectors so that you can insert them into the male heads of the battery.

The connectors will go straight into the battery. Fish finder can be easily wired to a fuse box with the help of silicone sealant and power drill. It is a very easy job to do.

If you follow the following steps it can be easily installed to a fuse box. INSTALL THE BINNACLE MOUNT. It is the mount of fish finder.

You should be careful about many factors. Find out the location where binnacle is to be mounted. As you look the helm of the ship should be very close to the fish finder.

Now we will demonstrate how you can wire your fish finder to your ship on your own. Decide the location where you would mount the fish finders binnacle. You should place it close to the helm of the ship and at a height so that you can look at it easily from anywhere on the ship.

When you place the binnacle seal it with the goop adhesive. Assuming that your fish finder comes with its fuse kit you will get all your connectors and wires. Wire the fish finder direct to the battery either the cranking battery or an auxiliary battery.

Dont take shortcuts and run the fish finder power wire into a block or switch panel. Wire your fish finder the right way and extend the Humminbird power wire directly to the battery using the correct type and gauge wire. Check and make sure one of the fused panels is not only on when the key is on you will probably want to wire the fishfinder to an always on circuit and just shut it off manually.

That way you can fish with the key off and still have sonar. Find a box that is large enough to contain your battery but nothing too big. Next to a battery youll have to fit a material that will also hold the battery.

So you have to look for a plastic toolkit box just a little bigger than your battery. Youll also require a good wire cutter a. March 7 2016 at 1242 pm 1604907.

If you wire it to the fusebreaker panel it isnt interference that would cause an issue provided its not on the same batter as your trolling motor but current draw that would cause your unit to turn off when you try and start the outboard. Connecting the Fishfinder Device. Once youve placed your battery safely in a waterproof box you can start connecting your device to it.

Being that the battery should be positioned at the lowest point of your boat youll need pretty long power cables to connect the fishfinder to a battery. Step 7 - Install and Wire New Fuse Box. Set the new fuse box in the location and attach it to the wall.

Use the same wires that you removed from the old box to connect to their individual terminals. Read each label and carefully wrap the exposed wire on the retaining screw. Tighten the screw and be careful not to fray the wires or break any of.

Inline fuse is fine you can buy a holder and appropriate amp fuse pretty easy. I would consider where on the fuse panel you decide to connect to. Some circuits are going to draw more amps than others so if you connect after the fuse on your panel to lets say the livewell pump the graph combined with another high demand circuit might pop the fuse possibly cause interference or worst case overheat a wire.

You should have two pairs of wires connected to your battery. One pair of heavy wires that go to your motor. Then one pair of wires that are about 10 or 8 gauge that go to a fuse block near the location of accessories.

This may be the console under the console or in a fuse block that is near a tiller seat location. You should use 6 gauge wire with proper connectors from your cranking battery to a stainless steel buse as close to finders as possible and avoiding as much other wiring as possible. That means dont take electrical tape and ball all wires together with finder wire dont run to your fuse box to small gauge wire and things like pumps lights stereo make ghost.

Also it is a good idea to have a 30 or 40 amp circuit breaker bolted to the starting battery to which is connected the wire that runs to the fuse block. This will protect the wire running to the fuse block. Then for your trolling motor batteries and trolling motor connections do the same thing.

Take a 50 amp circuit breaker and bolt it to. How to Install your Humminbird Helix Fish finder the right way. Part 2 is here httpsyoutubexz0I-qt9cB0.

Aside from the installation steps you would also want to learn how to wire the fish finder into your fuse box. Make sure you have everything you need from both lists before you start. Installing the Display Unit.

First you need to determine how those wires are powered. They may not go to any switch and the red may be always hot. The purplewhite is likely for lighting and may be powered through the anchor light circuit.

Isnt there an inline fuse in the wiring harness that came with the fish finder. Where are my manners. The unit fuse sizes are 3A each.

Some of the larger newer units take a 4A or 5A fuse. Humminbird SOLIX 12 SI SOLIX 12 SI G3 SOLIX 10 SI G3 Helix 15 CHIRP MEGA SI GPS G4N Helix 12 CHIRP SI GPS G3N Helix 12 CHIRP SI GPS G4N Helix 10 CHIRP DI GPS G3N Helix 8 CHIRP SI GPS G4N Helix 7 CHIRP SI GPS G3 MEGA 360. Lowrance include a fuse and fuse holder with the sounder I believe its a 3 amp fuse.

The unit draws roughly 162 amps per hour. I plan on connecting from the battery a short length of larger gauge wire 10GA to the fuse holder the from the fuse holder another long length 25m 10GA to the smaller wire 18GA of the sounder power lead. Apr 20 2021.

I bought a 2003 Tracker PT175 that I wish to install a new fish finder on the bow. I pulled the pre-wired bow lead up and checked for power but it has none. The wire colors are black and purple wred stripe.

I attempted to trace the wires back to the console and found a lead set with same colors and attached to the fuse block. How to easily wire and mount a fish finder to any kayak UNDER 10 minutes Watch Part 1 - Lowrance features and demo - httpsyoutubepgrglgturVUClick on A. The correct wire size for each cable depends on the length of the wire run and the fuse blocks maximum amp load.

On to the bow fish finder. Using only marine-grade wire shrink tubing fuse.