Mounting a fishfinder transducer on a pontoon boat

Place the transducer mounting bracket against the base of the mounting rack. Alternatively you can also purchase extension cables if you still dont have enough cord to work with.

Of course knowing which direction youre aiming for isnt enough.

Mounting a fishfinder transducer on a pontoon boat. In optimal situations the monitor to your fish finder should be mounted near the captains chair which would mean that your transducer should go under the right pontoon. Alternatively you can also purchase extension cables if you still dont have enough cord to work with. FishFinder and Transducer Mount for Pontoons Float Tubes - YouTube.

FishFinder and Transducer Mount for Pontoons Float Tubes. That means you should mount your transducer on the same side of your monitor. Usually on the starboard side.

Of course knowing which direction youre aiming for isnt enough. You need to pick an appropriate spot on the ship for mounting. Thankfully the design of pontoon boats makes it.

Fixing a transducer is a very easy step ie. Drill double holes at a 14 portion at below of the fish finder mounting brackets of your pontoon boat. You must verify that the tube is not punctured.

After putting it connect the transducer fixing with nut washer and with bolts. Originally when we purchased the boat the transducer was mounted to the back of a pontoon tube. Unfortunately the mount was one that did not have the flip-up feature found in the newer fishfinder models.

Basically it did not flip up when bumped from the front or when cruising at high speeds as the newer models do. Eventually after a couple of beachings the transducer. Its at the back of the pontoon log close to the bottom.

Think of the back as a dinner plate. Weld a U shaped aluminim bracket so it does not extend below the pontoon. Only the transducer should extend slightly below the log.

If the bracket hangs down below you create more drag and heaven knows on a toon there is already enough drag. I assume you have mounted it on the rear stern of the left port side. Should be a bolt where you can loosen adjust the angle that helped for me.

Seems like boats that dont really plane have a hard time reading the depth maybe too much cavitation or prop turbulance. Look at the rear of the pontoon boat. One of the pontoons will have a mounting rack attached.

The depth finder transducer mounting bracket will mount to this rack. Place the transducer mounting bracket against the base of the mounting rack. The transducer mounting bracket will have holes for the mounting screws.

Assemble the transducer and perform the initial mounting steps Most transom mount type transducers will have a pivot bolt that needs to be inserted through the pivot arm and assembly bracket. Hand tighten the pivot bolt then insert the pivot arm assembly into the mounting bracket. Outrigger style transducer mount for fiberglass and aluminum boats.

Allows the user to place the transducer at the front of the boat to see what is directly below. Removes the transducer from the trolling motor to prevent transducer wire from winding on the motor and removes potential for interference from the motor electronics. Most installation manuals will tell you to make it dead-even or slightly below the bottom and Ive found it best to mount the leading edge of the transducer even with the bottom edge of the boat and cock it back ever so slightly so the back of the transducer is about 116th of an inch lower then the bottom of the boat.

Our Fish Finder Mounts and transducer mounts make it easy to mount and power a fish finder and transducer on your Outcast Pontoon Classic Accessories Pontoon or any other personal inflatable pontoon boat pontoon raft or pontoon kick boat. I cut a length of aluminum 1 wide and 15 deep and mounted the transducer to one end and put a 90 degree bend in the top 2 Then I cut a second piece about 6 long and drilled two holes to match the 2 holes in the handle at the back of the toon. The easiest way to install a transducer on a boat or kayak.

Dont drill holes or use glues when installing your transducer. Rather use our magnetic transducer mounts. Works on all materials.

Also get the best transducer mounting solutions for your inflatable boat or kayaks here. We are making transducer mounting easy. Place the transducer around 116 inch under the hulls extended waterline.

Then execute each step. Mounting the transducer on a fiberglass boat will require you to focus on the transom and bottom joint. AlChase USA Member Posts.

In Electrical System Discussions for Godfrey Pontoon Tritoons. Hi I received a Garmin fishfinder as a Christmas present. Its getting close to boating season in upstate NY and I really dont have a clue about installing it.

I believe the transducer should be easy enough as. These transducers shoot an incredibly thin one-degree 455- or 800-Khz in the case of the Lowrance beam so it can thread the needle right in-between the outdrive and the transom of the boat. Here are a couple of shots of how it looks on my 22 Glacier Bay.

The side imager is mounted to starboard of the outdrive with the down looker to port. April 26 2010 at 730 pm 866994. Id mount a transducer plate near the bottom of my pontoon then attatch the transducer to the plate.

Secure the plate tot he pontoon with a good silicone adhesive worked for me. Phoenix AZ formerly from the NW Burbs Minneapolis MN USA. Pole Arm Transducer Mount for Pontoon Boats and Plastic Jon Boats - YouTube.